Подобрать дамп для 3516CV323
Добавлено: 31 окт 2023, 14:21
Добрый день, прошу помощи в подборе дампа для IP в/к одного отечественного производителя.
main 3516cv323_BRD_v0.3
SPI Nand память W25NO1GVZ
ниже вывод данных терминала. Поиск по hi3516cv300 есть варианты, но в них память с меньшим объемом. Их у меня несколько , все не определяются. На кнопку сброс реагирует (по потреблению смотрю) , заводской номер не пингуется
main 3516cv323_BRD_v0.3
SPI Nand память W25NO1GVZ
ниже вывод данных терминала. Поиск по hi3516cv300 есть варианты, но в них память с меньшим объемом. Их у меня несколько , все не определяются. На кнопку сброс реагирует (по потреблению смотрю) , заводской номер не пингуется
- hi3516cv300 System startup
U-Boot 2010.06 (Oct 17 2017 - 09:12:01)
Check Flash Memory Controller v100 ... Found
SPI Nand(cs 0) ID: 0xef 0xaa 0x21 Name:"W25N01GV"
Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4bit/512
SPI Nand total size: 128MB
MMC:
EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
No EMMC/MMC/SD device found !
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
hisilicon # help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootss - boot from snapshot image
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
ddr - ddr training function
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
getinfo - print hardware information
go - start application at address 'addr'
help - print command description/usage
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - mmcinfo <dev num>-- display MMC info
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
sf - SPI flash sub-system
tftp - tftp - download or upload image via network using TFTP protocol
version - print monitor version
hisilicon # printenv
bootargs=mem=70M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=yaffs2 rw mtdparts=hinand:1M(boot),5M(kernel),15M(rootfs),-(user)
bootcmd=nand read 0x82000000 0x100000 0x500000;bootm 0x82000000
bootdelay=1
baudrate=115200
ethaddr=00:00:23:34:45:66
ipaddr=192.168.1.10
serverip=192.168.1.2
netmask=255.255.255.0
bootfile="uImage"
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06 (Oct 17 2017 - 09:12:01)